No need for tools! Designed specifically for use with the Pro Pool Lift™. Quickly remove the Pro Pool Lift™ from your deck without the use of tools and re-install using the durable, hand knobs to tighten the lift down to the deck. The Quick Attach Anchor Kit offers an affordable alternative to a portable unit. Get the most out of your Quick Attach Anchor Option by purchasing the Pro Pool Lift™ Transport Cart, Item F-428HT, to transport the lift from poolside to storage and back again. This option does not affect the lifting capacity of The Pro Pool Lift™.
ADA REQUIREMENTS:
The PRO POOL LIFTTM is designed and manufactured to be 100% ADA compliant. But for the
installed lift to be 100% compliant the installation must meet the requirement for CLEAR DECK
SPACE as shown in the diagram to the left. To be compliant, install the lift at 14 inches [357mm]
(the maximum setback) from the pool edge, and make sure the deck has the required CLEAR
DECK SPACE as shown.
NOTE: ADA requires a deck slope of no greater than 1:48.
NOTE: The ADA requires the seat to go at least 18” into the water. To make sure the lift has enough clearance the lift should be installed at a location with 44”-48” of depth (deck to pool floor).
4 –POINT PRE-SET ANCHOR INSTALLATION
NOTE: THE 4-POINT PRESET ANCHOR CAN BE INSTALLED IN EITHER A NEW POOL DECK OR AN EXISTING DECK. BEFORE INSTALLING MAKE SURE THE WATER-DRAFT IS 12” OR LESS (DECK TO WATERLINE). INSTALL THE LIFT AT A LOCATION WITH 44” TO 48” OF DEPTH. RETRO-FIT INSTALLATION / EXISTING DECK APPLICATION
TOOLS REQUIRED:
MARKING PEN/PENCIL LEVEL
1-1/4” CORE DRILL BIT HIGH STRENGTH ANCHOR ADHESIVE CORE DRILL TAPE MEASURE HAMMER CHISEL
1. Locate the anchor jig and the FOUR (4) anchor bolts. FIGURE 1
2. Using the anchor jig plate smaller holes as a template, mark the FOUR (4) hole locations on the deck. The front anchor must be no more than 14 inches [356mm] from the pool wall. FIGURE 3. Make sure to keep the two rear anchor holes parallel to the pool wall.
3. Remove the 1” hex nuts from the anchor bolts. Core Drill a 1-1/4” [32mm] diameter hole at the FOUR (4) locations marked from step 1. Drill to a depth of 4” to 5” [10cm to 13cm].
4. Remove the core from the hole with a chisel and hammer if necessary. Clean out all four holes completely.
5. Fill each hole approximately ½ full with high strength anchor adhesive.*
6. Ground at least one anchor bolt to an existing bonding grid or appropriate ground source per local codes.
7. Install the FOUR (4) anchor bolts into the epoxy filled holes. Make sure that the top of the bolts will be flush with the top of the pool deck. (NOTE: To make positioning of the anchors easier the ½” bolts may be temporarily installed in the anchors to give you something to hold onto.)
8. Let the adhesive cure as per the manufacturer’s instructions before installing the PRO POOL LIFTTM.
* Use HILTI HIT HY-150 or SIMPSON ET22 StrongTie anchor adhesive
or equivalent.
NEW CONSTRUCTION: ANCHOR INSTALLATION
When the lift is installed on a new deck, the slab should be a minimum of 6” [15cm] thick at the lift location, and should be reinforced with #4 reinforcing bar at 10” [25.4cm] on center in each direction. The total pad area should be 3 feet [92cm] wide (from the edge of the pool back) by 3 feet [92cm] long.
1. Locate the preset anchor jig assembly and the four (4) anchor bolts. Mount the anchor bolts to the jig plate as shown in FIGURE 2.
2. Ground the jig plate using the attached bronze grounding lug. Check local codes for
anchor grounding.
3. Locate the jig assembly at the desired pool location. The front anchor (centerline)
must be no more than 14” [35.6cm] from the pool wall as shown in FIGURE 3.
Make sure to keep the front two anchor holes parallel to the pool wall.
4. Make sure the anchor assembly is plumb and level – secure the anchors, and then
pour the deck.
LIFT INSTALLATION AND REMOVAL
Once the 4-Point Preset Anchor has been installed and allowed to set for at least 48
hours, the pool lift may be installed and operated. The Quick Attach Anchor Bolts will be used to fix the lift safely and securely to the pool deck. STEP 1: Using a hand-truck or the Aqua Creek Products Transport Cart (F-428HTshown – sold separately) carefully
move the Pro Pool lift to the anchor location. Orient the anchor-bolt holes in the base-plate of the lift over the four (4) anchors. Lower and adjust the lift until all four holes
line-up.