Shopping Cart
Your cart is empty.
Browse Categories
Browse by Manufacturer

Loctite Fixmaster Underwater Repair Pool Epoxy

Loctite Fixmaster Underwater Repair Pool Epoxy
Price: $27.50
Item Number: AMG82093
Manufacturer: Loctite
This one-part putty-like material is ideal for plumbing, irrigation and marine applications. It is hand kneadable and fully cures in 1 hour. Just cut off what you need and mix together. Sold in 4 oz. quantities.

PRODUCT DESCRIPTION

LOCTITE® Fixmaster® Metal Magic Steel™ provides the following product characteristics:

Technology Epoxy

Chemical Type Epoxy

Appearance (uncured) Metallic blackLMS

Components One part - requires no mixing

 

Cure Room temperature cure

 

Application Bonding

Specific Benefit ● Cures under water and will adhere to most damp surfaces

● Adheres to most types of clean surfaces

● Cures in 10 minutes for fast repairs

● Epoxy adhesive stick applies like putty and cures to a steellike finish

 

LOCTITE® Fixmaster® Metal Magic Steel™ is a versatile, single component, easy to use, steel filled epoxy repair putty. It is applied like a putty and when cured it has a high compressive strength and good adhesion to most surfaces.  This product stops leaks in pipes and tanks, fills oversized bolt holes, smoothes welds, and repairs non-structural defects in castings holes in tanks. This product is typically used in applications with an operating range of -30 °C to +121 °C.

 

NSF International

Certified to ANSI/NSF Standard 61 for use in commercial and residential potable water systems not exceeding 82° C.

 

TYPICAL PROPERTIES OF UNCURED MATERIAL

Coverage 40 cm² @ 6 mm thick per tube (16 in² @ 0.25 in thick per tube)

 

TYPICAL CURING PERFORMANCE

Curing Properties

Cure Time @ 25 °C, minutes 10 Working Time @ 25 °C, minutes 2.5 to 5.0LMS

 

TYPICAL PROPERTIES OF CURED MATERIAL

Cured for 1 hour @ 25 °C

Physical Properties:

Shore Hardness, ISO 868, Durometer D >70LMS

Tensile Strength, ISO 527-2 N/mm² 17

(psi) (2,500)

 

TYPICAL PERFORMANCE OF CURED MATERIAL

Adhesive Properties

Cured for 1 hour @ 25 °C

Lap Shear Strength, ISO 4587:

Steel (grit blasted) N/mm² ≥3.45LMS (psi) (≥500)

Aluminum (acid etched): 0.125 mm gap N/mm² 4.8 (psi) (700)

Compressive Shear Strength, ISO 10123:

Steel pins and collars N/mm² 83 (psi) (12,000)

 

GENERAL INFORMATION

This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.  For safe handling information on this product, consult the Material Safety Data Sheet (MSDS).

 

Directions for use

1. CAUTION: Do not apply to surfaces above 66 °C.

2. Clean and dry application surface, if possible. For maximum adhesion, clean and sand the surface. Clip

desired amount, remove plastic, roll briskly betweeen hands, twist and knead until uniform color.

3. Firmly apply for patch, repair or bonding.

4. For a smooth finish, wet a cloth or finger with water and smooth.

 

Technical Tips for Working With Epoxies

Working time and cure depends on temperature and mass:

● The higher the temperature, the faster the cure.

● The larger the mass of material, the faster the cure. To speed the cure of epoxies at low temperatures:

● Store epoxy at room temperature.

● Pre-heat repair surface until warm to the touch. To slow the cure of epoxies at high temperatures:

● Mix epoxy in small masses to prevent rapid curing.

● Cool putty down.

Product Reviews

(0 Ratings, 0 Reviews)